• FAQ  • Search  • Memberlist  • Usergroups   • Register   • Profile  • Log in to check your private messages  • Log in 

Outer diameter shank size of Callet mouthpieces



 
Post new topic   Reply to topic    trumpetherald.com Forum Index -> Jerome Callet
View previous topic :: View next topic  
Author Message
jhl
Regular Member


Joined: 06 Jun 2017
Posts: 18

PostPosted: Thu Nov 05, 2020 9:54 am    Post subject: Outer diameter shank size of Callet mouthpieces Reply with quote

I have a few Callet mouthpieces, from the 90s, I believe. Haven't played them in quite a while and when I just tried them I noticed they bottomed out in all my trumpet receivers, including some fairly small I.D. ones (like an two 30s peashooters, one from Conn and one from Buescher). Was this part of Jerome's design? Did his Kanstul made horns come with especially small receivers? Any other ideas.
Back to top
View user's profile Send private message
JayKosta
Heavyweight Member


Joined: 24 Dec 2018
Posts: 1227
Location: Endwell NY USA

PostPosted: Thu Nov 05, 2020 11:57 am    Post subject: Reply with quote

Compare the open ends (the OD) of the Callet mpc with other brands to see if they are smaller.
It might also be that the taper of the Callet shaft is less than others.
The tapers can be compared by placing the shanks on a flat surface, and then placing another FLAT item (maybe a metal ruler or bar) on top of the shanks - the top bar should rest evenly on both shanks, no tilts or wobbles.
The 'standard' size and taper of trumpet mpc is known as Morse 1 .

Jay
_________________
King Super 20 (S2 1048, HN White)
Bach 7
The 'next note' is the most important one.
Don't take a '20 minute mouthpiece' to a 1 hour session.
http://users.hancock.net/jkosta/2020_Oct_08_web.jpg Summer's been and gone, Winter's coming on.
Back to top
View user's profile Send private message
lipshurt
Heavyweight Member


Joined: 24 Feb 2008
Posts: 2355
Location: vista ca

PostPosted: Thu Nov 05, 2020 1:24 pm    Post subject: Reply with quote

“Morse 1” refers to a specific small end and large end dimensions. So a mouthpiece is not a “Morse 1”. A Morse 1, 2, 3 etc all have the same rate of taper. Mouthpieces have that same rate of taper .050 over 1.000

You can call that a Morse taper, but not a Morse 1
_________________
Mouthpiece Maker
vintage Trumpet design enthusiast
www.meeuwsenmouthpieces.com
www.youtube.com/lipshurt
Back to top
View user's profile Send private message Visit poster's website
jhl
Regular Member


Joined: 06 Jun 2017
Posts: 18

PostPosted: Thu Nov 05, 2020 1:51 pm    Post subject: Callet trumpet mouthpiece narrow shank Reply with quote

These Callet mpcs are at most 1/4" longer than standard, but are a smidge shorter than a standard Schilke mpc. They don't bottom out because of the diameter at the end of the shank, but because of the narrowing taper coupled with their length. Still waiting to get input from someone familiar with Callet mpcs. BTW -- these are all for sale in the Marketplace. Each has a pristine rim and shank.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    trumpetherald.com Forum Index -> Jerome Callet All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group