View previous topic :: View next topic |
Author |
Message |
trumpetp1 Veteran Member
Joined: 04 Nov 2007 Posts: 136 Location: Pennsylvania
|
Posted: Sun May 12, 2019 9:30 am Post subject: |
|
|
interfx wrote: | https://www.holtonloyalist.com/
HoltonLoyalist.com is still up and running! Although the email is overrun with spam, so I usually just check here on TH when people have questions.
The finger button examples you shared were not from the factory - I've seen an example a few years ago on a stencil (student level) horn. I would guess they were added to teach a student to not let their fingers overlap the valve caps.
Hope that helps, send me a PM here on TH, if you have specific question.... |
Well, it's good to know that HL.com is still up and running. However, I'll not expect any reply to my email, in any case.
I wasn't completely sold on the notion that these were factory, but the solder work is quite good and the silver of the finger "guards" and the mother-of-pearl inlays appear to be of a similar age as the horn...at least, to my eyes.
Regardless the origin, I guess these finger buttons are as eccentric as myself. Woot. _________________ trumpetp1 |
|
Back to top |
|
|
LittleRusty Heavyweight Member
Joined: 11 Aug 2004 Posts: 12663 Location: Gardena, Ca
|
Posted: Sun May 12, 2019 10:39 am Post subject: |
|
|
I am not sure that visual or any other examination of the valve caps can prove factory or after market. There are many techs that do fine work and some are former factory workers. And the age won’t indicate much either because they probably had good techs back when the valve caps were made.
On the other hand if the caps were high build quality and the guards low you would have your answer. |
|
Back to top |
|
|
trumpetp1 Veteran Member
Joined: 04 Nov 2007 Posts: 136 Location: Pennsylvania
|
Posted: Sun May 12, 2019 6:51 pm Post subject: |
|
|
LittleRusty wrote: | I am not sure that visual or any other examination of the valve caps can prove factory or after market. There are many techs that do fine work and some are former factory workers. And the age won’t indicate much either because they probably had good techs back when the valve caps were made.
On the other hand if the caps were high build quality and the guards low you would have your answer. |
Absolutely agree. As I said in my first post in this thread, I'm not sure I'm taken with them. Still, they look nice...and, certainly start some conversation. I guess I'll just never know. _________________ trumpetp1 |
|
Back to top |
|
|
LittleRusty Heavyweight Member
Joined: 11 Aug 2004 Posts: 12663 Location: Gardena, Ca
|
Posted: Sun May 12, 2019 6:56 pm Post subject: |
|
|
You need to find a number with lots of fast notes and fingerings. Learn it cold and then play it during warmups. Tell your section mates that the special caps are the reason your fingering is so excellent. |
|
Back to top |
|
|
trumpetp1 Veteran Member
Joined: 04 Nov 2007 Posts: 136 Location: Pennsylvania
|
Posted: Thu May 16, 2019 9:18 am Post subject: |
|
|
LittleRusty wrote: | You need to find a number with lots of fast notes and fingerings. Learn it cold and then play it during warmups. Tell your section mates that the special caps are the reason your fingering is so excellent. |
Ha! That would be almost priceless. Very tempting. _________________ trumpetp1 |
|
Back to top |
|
|
J. Landress Brass Veteran Member
Joined: 29 May 2006 Posts: 425 Location: New York City
|
Posted: Fri May 17, 2019 6:51 am Post subject: |
|
|
About a decade ago I did something quite similar for that for a player who had 2 missing tops of their fingers from an accident, It allowed him to wedge the nubs into the buttons and push the valves down without them slipping off the buttons. I would assume this was done for a similar reason. _________________ Josh Landress
J. Landress Brass, LLC.
38 West 32nd Street, STE 908, NY, NY 10001
646-922-7126
www.jlandressbrass.com |
|
Back to top |
|
|
trumpetp1 Veteran Member
Joined: 04 Nov 2007 Posts: 136 Location: Pennsylvania
|
Posted: Tue May 21, 2019 10:15 am Post subject: |
|
|
J. Landress Brass wrote: | About a decade ago I did something quite similar for that for a player who had 2 missing tops of their fingers from an accident, It allowed him to wedge the nubs into the buttons and push the valves down without them slipping off the buttons. I would assume this was done for a similar reason. |
Interesting. I went to university in the early 2000's with a fellow who had a similar problem, but not this sort of finger button solution.
Thank you for your input! _________________ trumpetp1 |
|
Back to top |
|
|
|