View previous topic :: View next topic |
Author |
Message |
1957Tim Veteran Member
Joined: 30 Oct 2004 Posts: 192 Location: Hannibal Missouri
|
Posted: Fri Apr 09, 2021 6:56 am Post subject: |
|
|
Quote: | Dale Proctor wrote:
Schilke mouthpieces typically have a slightly longer shank that tapers to a smaller diameter, so it inserts into the receiver farther. I’ve had them bottom out in Bach instruments before seating fully. I think they are set up to produce zero gap in Schilke instruments. |
Hey Dale, I have a quick question for you. What did you do to correct the Schilke mouthpiece bottoming out problem? One of the guys in the brass band I play in recently purchased a Schilke mouthpiece and it doesn’t fully seat in the Bach cornet he’s playing. We tried the piece in my Flip Oakes cornet, and another players Yamaha cornet and it didn’t seat well in either of these cornets. When I saw you comment it made me wonder if you had a fix for that problem.
I thank you in advance for sharing your expertise.
-1957Tim |
|
Back to top |
|
|
Billy B Heavyweight Member
Joined: 12 Feb 2004 Posts: 6130 Location: Des Moines
|
Posted: Fri Apr 09, 2021 11:43 am Post subject: |
|
|
James Becker wrote: | Bflatman wrote: | I trust james of course and it is an exercise worth doing but I dont think we can assume it will always be present on all instruments.
I think more work is needed on this topic.
I do not wish to claim the gap issue is like wearing lucky socks but I am hoping for something more convincing than is available now. |
No. More work is is NOT needed regarding this subject. There's plenty of information online from Reeves, GR, Pickett-Blackburn and others. There's even a Doctoral thesis on mouthpiece gap published in the the ITG Journal if you care to seek it out.
Before you go on speculating weather it's a legitimate thing or not, I suggest you dig deeper. |
_________________ Bill Bergren |
|
Back to top |
|
|
Dale Proctor Heavyweight Member
Joined: 26 May 2005 Posts: 9379 Location: Heart of Dixie
|
Posted: Fri Apr 09, 2021 12:30 pm Post subject: |
|
|
1957Tim wrote: | Quote: | Dale Proctor wrote:
Schilke mouthpieces typically have a slightly longer shank that tapers to a smaller diameter, so it inserts into the receiver farther. I’ve had them bottom out in Bach instruments before seating fully. I think they are set up to produce zero gap in Schilke instruments. |
Hey Dale, I have a quick question for you. What did you do to correct the Schilke mouthpiece bottoming out problem? One of the guys in the brass band I play in recently purchased a Schilke mouthpiece and it doesn’t fully seat in the Bach cornet he’s playing. We tried the piece in my Flip Oakes cornet, and another players Yamaha cornet and it didn’t seat well in either of these cornets. When I saw you comment it made me wonder if you had a fix for that problem.
I thank you in advance for sharing your expertise.
-1957Tim |
Use a small tubing cutter to take off about 1/8” from the end. Go slow with it so the end isn’t deformed, and then ream out the end to remove any lip if needed. A temporary solution would be to try a layer of scotch tape on the shank to keep it from inserting quite so far, and would probably be a good test before cutting it. _________________ "Brass bands are all very well in their place - outdoors and several miles away ." - Sir Thomas Beecham |
|
Back to top |
|
|
hose Heavyweight Member
Joined: 29 Jun 2003 Posts: 1854 Location: Winter Garden, FL
|
Posted: Fri Apr 09, 2021 1:09 pm Post subject: |
|
|
Gap is mostly player specific, but to further complicate the issue, different horns have a "sweet spot" for the best playing gap. I wouldn't take the chance of ruining a mpc by shaving the shank by hand. Here is a quote that Roy Lawler posted in 2003 here on TH.
"If you want the most change in your slotting set your gap! Valve alignments are fine but not the focus of the problem. Here is the key! Make sure you use the mouthpiece you are going to play to set the gap! All of the mouthpieces very. Here is the formula.
Classical players .125 to ..150 This gives you more center (slots)
Commercial players .050 to .125 This gives you a bendable center.
Now you can experiment in between these numbers to find an optimum for you. Remeber this is based on the fact you like the blow of the leadpipe overall. Also just because you set your gap with your favorite MP and buy another just like it (most of all Bach) it wont be the same gap."
Roy Lawler[/i] _________________ Dave Wisner
Picketts
Yamaha 6335RC
Yamaha 8335RS
Lawler Flugel
Kanstul cornet |
|
Back to top |
|
|
|